Hi Marius, I did so, I can see libvirtd has been installed on both nodes and active but they are not appearing as support service in the command Openstack-status in both nodes. Here is my answers file: http://pastebin.com/sLQiGhLy Here is Openstack-Status for controller node: http://pastebin.com/8zTvcDfT Here is Openstack-Status for compute node: http://pastebin.com/aSFw7dLF What do you advise? Thanks, Ashraf From: Marius Cornea [mailto:marius@remote-lab.net] Sent: Tuesday, 9 February 2016 2:37 PM To: Ashraf Hassan <asma2103(a)yahoo.com&gt; Cc: rdo-list(a)redhat.com Subject: Re: [Rdo-list] Deploying Openstack with Packstack Minimal, packstack does the installation for you. Just make sure you have the repos mentioned in the guide. Thanks. On 09 Feb 2016, at 14:26, Ashraf Hassan <asma2103(a)yahoo.com&gt; wrote: Hi Marius, But what the is the perquisite as RHEL/Centos Installation for Packstack to work for both Controller and Compute nodes (i.e. Minimal Install, Compute Node, Infrastructure Server, ...etc.) Thanks, Ashraf On Monday, February 8, 2016 10:28 PM, Marius Cornea <marius(a)remote-lab.net&gt; wrote: Hi, Here is the quickstart link: https://www.rdoproject.org/install/quickstart/ You can get started with a minimal CentOS/RHEL. For deploying the 2 node deployment you can generate an answer file(packstack --gen-answer-file) and adjust the IP addresses for CONFIG_CONTROLLER_HOST and CONFIG_COMPUTE_HOSTS. Please note that you need ssh key-based authentication for those 2 hosts. Thanks, Marius On Mon, Feb 8, 2016 at 5:38 PM, Ashraf Hassan <asma2103(a)yahoo.com&gt; wrote: > Hi Experts, > I want to test deploying Openstack using Packstack on 2 nodes using > answers file: > 1- Node will act as a controller node. > 2- Node will act as a compute node. > What is the level of installation is needed for RHEL/Centos (Minimum, > Hypervisor host, or etc...) > Can someone advise please? > Thanks, > > Ashraf > > > > > _______________________________________________ > Rdo-list mailing list > Rdo-list(a)redhat.com > https://www.redhat.com/mailman/listinfo/rdo-list > > To unsubscribe: rdo-list-unsubscribe(a)redhat.com

On 16 Feb 2016, at 09:59, Ashraf Hassan <asma2103(a)yahoo.com&gt; wrote: Hi Marius, It says both are up, is that OK?, Is that OK as well not to see libvirtd in the support services?: (keystone_admin)]# nova hypervisor-list +----+----------------------------------+-------+---------+ | ID | Hypervisor hostname | State | Status | +----+----------------------------------+-------+---------+ | 1 | servera.refmobilecloud.ux.nl.tmo | up | enabled | | 2 | serverb.refmobilecloud.ux.nl.tmo | up | enabled | +----+----------------------------------+-------+---------+ -----Original Message----- From: Marius Cornea [mailto:marius@remote-lab.net] Sent: Tuesday, 16 February 2016 12:19 AM To: Ashraf Hassan <asma2103(a)yahoo.com&gt; Cc: rdo-list <rdo-list(a)redhat.com&gt; Subject: Re: [Rdo-list] Deploying Openstack with Packstack Hi, The output looks good to me, seems that the openstack services are running. I don't think openstack-status is supposed to show the libvirtd status though. You can run 'nova hypervisor-list' and see if the 2 hosts show as active. Thanks, Marius > On Tue, Feb 16, 2016 at 12:10 AM, Ashraf Hassan <asma2103(a)yahoo.com&gt; wrote: > Hi Marius, > > I did so, I can see libvirtd has been installed on both nodes > and active but they are not appearing as support service in the > command Openstack-status in both nodes. > > Here is my answers file: http://pastebin.com/sLQiGhLy > > Here is Openstack-Status for controller node: > http://pastebin.com/8zTvcDfT > > Here is Openstack-Status for compute node: > http://pastebin.com/aSFw7dLF > > What do you advise? > > Thanks, > > Ashraf > > From: Marius Cornea [mailto:marius@remote-lab.net] > Sent: Tuesday, 9 February 2016 2:37 PM > To: Ashraf Hassan <asma2103(a)yahoo.com&gt; > Cc: rdo-list(a)redhat.com > Subject: Re: [Rdo-list] Deploying Openstack with Packstack > > > > Minimal, packstack does the installation for you. Just make sure you > have the repos mentioned in the guide. Thanks. > > > On 09 Feb 2016, at 14:26, Ashraf Hassan <asma2103(a)yahoo.com&gt; wrote: > > Hi Marius, > > But what the is the perquisite as RHEL/Centos Installation for > Packstack to work for both Controller and Compute nodes (i.e. Minimal > Install, Compute Node, Infrastructure Server, ...etc.) > > > > Thanks, > > > > Ashraf > > > > > > > > > > On Monday, February 8, 2016 10:28 PM, Marius Cornea > <marius(a)remote-lab.net&gt; > wrote: > > > > Hi, > > Here is the quickstart link: > https://www.rdoproject.org/install/quickstart/ > > You can get started with a minimal CentOS/RHEL. For deploying the 2 > node deployment you can generate an answer file(packstack > --gen-answer-file) and adjust the IP addresses for > CONFIG_CONTROLLER_HOST and CONFIG_COMPUTE_HOSTS. Please note that you > need ssh key-based authentication for those 2 hosts. > > Thanks, > Marius > > >> On Mon, Feb 8, 2016 at 5:38 PM, Ashraf Hassan <asma2103(a)yahoo.com&gt; wrote: >> Hi Experts, >> I want to test deploying Openstack using Packstack on 2 nodes >> using answers file: >> 1- Node will act as a controller node. >> 2- Node will act as a compute node. >> What is the level of installation is needed for RHEL/Centos >> (Minimum, Hypervisor host, or etc...) >> Can someone advise please? >> Thanks, >> >> Ashraf > > >> >> >> >> >> _______________________________________________ >> Rdo-list mailing list >> Rdo-list(a)redhat.com >> https://www.redhat.com/mailman/listinfo/rdo-list >> >> To unsubscribe: rdo-list-unsubscribe(a)redhat.com