Re: [rdo-list] [TripleO] quickstart undercloud problems.

Did you ever type up a lengthy email to a list, looking for help, and then the moment you hit send, a lightbulb goes on, and you fix your ow problem? Apparently when I built my test system, my build environment turned on iptables (like I've told it to) and it was too restrictive. I flushed iptables, and disabled puppet (so it wouldnt turn it back on again) rebooted the undercloud vm, and guess what? It's on the network now. Quickstart is now able to communicate with the undercloud vm. To anyone reading this, having a similar problem.... Check iptables. :headdesk: ----------- RHCSA, RHCE, RHCVA (#110-011-426) gpg public key: https://keybase.io/gangrif - or - MIT's public key server, pgp.mit.edu ----- Original Message ----- From: "war" <war(a)undrground.org&gt; To: rdo-list(a)redhat.com Sent: Saturday, November 19, 2016 9:43:49 AM Subject: [rdo-list] [TripleO] quickstart undercloud problems. Good Morning rdo-list, im attempting to get a test openstack install up and running using RDO, and ooo quickstart on Centos 7. I'm following the brief instructions found here: https://www.rdoproject.org/tripleo/ I am running quickstart from the same system i'm targeting. So i'm setting $VIRTHOST to localhost, or the local IP of the box (192.168.3.10), I've tried it both ways, which doesn't seem to make a difference. I'm running quickstart as my local use, not the stack user. Initially things appear to run along nicely, the script downloads images and whatnot, it even starts up the undercloud vm as the stack user. [stack@fog ~]$ virsh list Id Name State ---------------------------------------------------- 2 undercloud running When quickstart gets to the point where it's attempting to determine the IP of the undercloud VM, it fails. I did a little digging on how exactly that works, and found that the script which it runs is not getting any results. mac=$(virsh dumpxml $VMNAME | awk -F "'" '/mac address/ { print $2; exit }') # Look up the MAC address in the ARP table. ip=$(ip neigh | grep $mac | awk '{print $1;}') I've tried these manually, and sure enough the mac address is not in ip neigh. stack@fog .quickstart]$ virsh dumpxml undercloud | awk -F "'" '/mac address/ { print $2; exit }' 00:e4:b2:54:b5:fb [stack@fog .quickstart]$ ip neigh | grep '00:e4:b2:54:b5:fb' | awk '{print $1;}' [stack@fog .quickstart]$ ip neigh | grep -v FAILED 192.168.3.1 dev enp13s0 lladdr 52:54:00:ab:d2:15 REACHABLE 192.168.3.251 dev enp13s0 lladdr 52:54:00:f2:90:b7 REACHABLE [stack@fog .quickstart]$ I did a virsh console on the undercloud vm, and reset it, so I could watch it boot, and I see the following in the boot messages: [FAILED] Failed to start LSB: Bring up/down networking. See 'systemctl status network.service' for details. I cant login to the undercloud vm, as I don't have the local username/pass. or I'd troubleshoot that further. As far as I can tell the undercloud system uses standard linux bridges to setup network communication, They appear present, but as they're not configured in the same manner i've used in the past, I can't be certain if they're working properly. [stack@fog ~]$ brctl show bridge name bridge id STP enabled interfaces brext 8000.525400af4796 no brext-nic tap0 brovc 8000.525400180812 no brovc-nic tap1 virbr0 8000.525400a3f6b5 yes virbr0-nic [stack@fog ~]$ ifconfig brext-nic brext-nic: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 52:54:00:af:47:96 txqueuelen 500 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 [stack@fog ~]$ ifconfig brovc-nic brovc-nic: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 52:54:00:18:08:12 txqueuelen 500 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 I've tried some other basics, like setting selinux to permissinv and re-trying (which was a long shot) and it didn't help. Any suggestions on what to tr next would be helpful. Thanks! ----------- RHCSA, RHCE, RHCVA (#110-011-426) gpg public key: https://keybase.io/gangrif - or - MIT's public key server, pgp.mit.edu _______________________________________________ rdo-list mailing list rdo-list(a)redhat.com https://www.redhat.com/mailman/listinfo/rdo-list To unsubscribe: rdo-list-unsubscribe(a)redhat.com