Re: [Rdo-list] TripleO quickstart problem by deploying the overcloud

Finally I got the TripleO installation running. After the virtual environment setup via: bash quickstart.sh $virthost If I run "*openstack undercloud install" *directly, the undercloud installation completes, but the following steps leads to an incomplete setup (I could reproduce this several times on our own hardware and on Rackspace Ironic powered :-) OnMetal servers): [stack@undercloud ~]$ . stackrc [stack@undercloud ~]$ openstack overcloud image upload [stack@undercloud ~]$ openstack baremetal import --json instackenv.json [stack@undercloud ~]$ ironic node-list +--------------------------------------+-----------+---------------+-------------+--------------------+-------------+ | UUID | Name | Instance UUID | Power State | Provisioning State | Maintenance | +--------------------------------------+-----------+---------------+-------------+--------------------+-------------+ | 57db4c06-7bb9-40c8-8530-6e9d5efb83c5 | control-0 | None | *None* | available | False | | 21af64b4-d3c3-4b63-ba97-aa14173a21be | compute-0 | None | *None* | available | False | +--------------------------------------+-----------+---------------+-------------+--------------------+-------------+ and as I mentioned earlier the "openstack baremetal configure boot" times out: [stack@undercloud ~]$ openstack baremetal configure boot Node 57db4c06-7bb9-40c8-8530-6e9d5efb83c5 power state is in transition. Waiting up to 120 seconds for it to complete. *Timed out* waiting for node 57db4c06-7bb9-40c8-8530-6e9d5efb83c5 power state. And I guess because the Power State is set to None! But if I run the following scripts by hand the installation completes successfully (in most cases): undercloud-install.sh undercloud-post-install.sh overcloud-deploy.sh overcloud-deploy-post.sh overcloud-validate.sh Only once by my last tests it failed after running: [stack@undercloud ~]$ bash overcloud-deploy.sh 2016-03-28 15:21:56 [Compute]: CREATE_COMPLETE state changed Stack overcloud *CREATE_FAILED* *Deployment failed: Heat Stack create failed.* And I had to delete the stack and re-deploy it again, which worked :-) [stack@undercloud ~]$ heat stack-delete overcloud [stack@undercloud ~]$ bash overcloud-deploy.sh [stack@undercloud ~]$ heat stack-list +--------------------------------------+------------+-----------------+---------------------+--------------+ | id | stack_name | stack_status | creation_time | updated_time | +--------------------------------------+------------+-----------------+---------------------+--------------+ | 8e588312-d839-4089-b123-3fa9b5e76c82 | overcloud | *CREATE_COMPLETE* | 2016-03-28T16:44:59 | None | +--------------------------------------+------------+-----------------+---------------------+--------------+ Here are the steps which might lead to a successful TripleO quickstart setup with a seed and baremetal host (virthost-01). (the seed / ansible host is a CentOS 7 machine (could be a VM running in VirtualBox on localhost on Mac or Windows for instance), the baremetal host needs 32 GB RAM, 2 nics and 150 GB Disk). On the seed / ansible host run: [root@seed ~]# yum -y update [root@seed ~]# yum install git -y [root@seed ~]# vim /etc/hosts <ip-virthost-01> virthost-01 [root@seed ~] git clone https://github.com/redhat-openstack/tripleo-quickstart/ [root@seed ~] cd tripleo-quickstart/ [root@seed ~] sudo bash quickstart.sh --install-deps [root@seed ~] reboot (not needed, but doesn't hurt :-)) [root@seed ~] ssh-keygen -t rsa [root@seed ~] ssh-copy-id -i ~/.ssh/id_rsa.pub virthost-01 [root@seed ~] ssh <ip-virthost-01> exit Deploy your virtual environment by running: [root@seed ~] *bash quickstart.sh virthost-01 * ################################## Virtual Environment Setup Complete ################################## Access the undercloud by: *ssh -F /root/.quickstart/ssh.config.ansible undercloud* *USE THIS: There are scripts in the home directory to continue the deploy:* undercloud-install.sh will run the undercloud install undercloud-post-install.sh will perform all pre-deploy steps overcloud-deploy.sh will deploy the overcloud overcloud-deploy-post.sh will do any post-deploy configuration overcloud-validate.sh will run post-deploy validation Alternatively, you can ignore these scripts and follow the upstream docs: First: *(DON’t use this!!!!!!!!!!!!!!!!!!!!!!!!!!!!!)* *openstack undercloud install* source stackrc Verify your Stack: [stack@undercloud ~]$ heat stack-list +--------------------------------------+------------+-----------------+---------------------+--------------+ | id | stack_name | stack_status | creation_time | updated_time | +--------------------------------------+------------+-----------------+---------------------+--------------+ | 8e588312-d839-4089-b123-3fa9b5e76c82 | overcloud | *CREATE_COMPLETE* | 2016-03-28T16:44:59 | None | +--------------------------------------+------------+-----------------+---------------------+--------------+ By the way, I'd love to see and help to have an complete installation guide for TripleO powered by RDO on the RDO site (the instack virt setup without quickstart on http://docs.openstack.org/ doesn't work and this might be changed through the RDO community power :-)). Thx, -Arash On Sat, Mar 26, 2016 at 3:52 AM, Adam Young <ayoung(a)redhat.com&gt; wrote: