[Rdo-list] Deploying Openstack with Packstack

[Ashraf Hassan]

Hi Marius,
      It says both are up, is that OK?, Is that OK as well not to see libvirtd in the support services?:
(keystone_admin)]# nova hypervisor-list
+----+----------------------------------+-------+---------+
| ID | Hypervisor hostname              | State | Status  |
+----+----------------------------------+-------+---------+
| 1  | servera.refmobilecloud.ux.nl.tmo | up    | enabled |
| 2  | serverb.refmobilecloud.ux.nl.tmo | up    | enabled |
+----+----------------------------------+-------+---------+

-----Original Message-----
From: Marius Cornea [mailto:marius at remote-lab.net] 
Sent: Tuesday, 16 February 2016 12:19 AM
To: Ashraf Hassan <asma2103 at yahoo.com>
Cc: rdo-list <rdo-list at redhat.com>
Subject: Re: [Rdo-list] Deploying Openstack with Packstack

Hi,

The output looks good to me, seems that the openstack services are running. I don't think openstack-status is supposed to show the libvirtd status though. You can run 'nova hypervisor-list' and see if the 2 hosts show as active.

Thanks,
Marius

On Tue, Feb 16, 2016 at 12:10 AM, Ashraf Hassan <asma2103 at yahoo.com> wrote:
> Hi Marius,
>
>       I did so, I can see libvirtd has been installed on both nodes 
> and active but they are not appearing as support service in the 
> command Openstack-status in both nodes.
>
>       Here is my answers file: http://pastebin.com/sLQiGhLy
>
>       Here is Openstack-Status for controller node:
> http://pastebin.com/8zTvcDfT
>
>       Here is Openstack-Status for compute node:
> http://pastebin.com/aSFw7dLF
>
>    What do you advise?
>
> Thanks,
>
> Ashraf
>
> From: Marius Cornea [mailto:marius at remote-lab.net]
> Sent: Tuesday, 9 February 2016 2:37 PM
> To: Ashraf Hassan <asma2103 at yahoo.com>
> Cc: rdo-list at redhat.com
> Subject: Re: [Rdo-list] Deploying Openstack with Packstack
>
>
>
> Minimal, packstack does the installation for you. Just make sure you 
> have the repos mentioned in the guide. Thanks.
>
>
> On 09 Feb 2016, at 14:26, Ashraf Hassan <asma2103 at yahoo.com> wrote:
>
> Hi Marius,
>
>     But what the is the perquisite as RHEL/Centos Installation for 
> Packstack to work for both Controller and Compute nodes (i.e. Minimal 
> Install, Compute Node, Infrastructure Server, ...etc.)
>
>
>
> Thanks,
>
>
>
> Ashraf
>
>
>
>
>
>
>
>
>
> On Monday, February 8, 2016 10:28 PM, Marius Cornea 
> <marius at remote-lab.net>
> wrote:
>
>
>
> Hi,
>
> Here is the quickstart link:
> https://www.rdoproject.org/install/quickstart/
>
> You can get started with a minimal CentOS/RHEL. For deploying the 2 
> node deployment you can generate an answer file(packstack
> --gen-answer-file) and adjust the IP addresses for 
> CONFIG_CONTROLLER_HOST and CONFIG_COMPUTE_HOSTS. Please note that you 
> need ssh key-based authentication for those 2 hosts.
>
> Thanks,
> Marius
>
>
> On Mon, Feb 8, 2016 at 5:38 PM, Ashraf Hassan <asma2103 at yahoo.com> wrote:
>> Hi Experts,
>>      I want to test deploying Openstack using Packstack on 2 nodes 
>> using answers file:
>>      1- Node will act as a controller node.
>>      2- Node will act as a compute node.
>>    What is the level of installation is needed for RHEL/Centos 
>> (Minimum, Hypervisor host, or etc...)
>>      Can someone advise please?
>> Thanks,
>>
>> Ashraf
>
>
>>
>>
>>
>>
>> _______________________________________________
>> Rdo-list mailing list
>> Rdo-list at redhat.com
>> https://www.redhat.com/mailman/listinfo/rdo-list
>>
>> To unsubscribe: rdo-list-unsubscribe at redhat.com
>
>
>
>