On 03/25/2016 01:15 PM, Arash Kaffamanesh wrote:
> Dan, thx!
>
> After running:
>
> [stack@undercloud ~]$ openstack baremetal configure boot
>
> nothing is get shown (and I'm somehow sure and guess that this step
> does not complete successfully, but my current knowledge ans a
> ooo-newbie doesn't allow to investigate this further for now :-)).
>
> And the introspection finishes too fast for my taste :-)
>
> [stack@undercloud ~]$ openstack baremetal introspection bulk start
>
> Setting nodes for introspection to manageable...
>
> Waiting for introspection to finish...
>
> Setting manageable nodes to available...
>
> Introspection completed.
>
>
> And yes, I've a baremetal machine with 32 GB RAM and 160 GB SSD disk.
>
> And if I run ironic node-show I get the last error which states: node
> state None does not match expected state.
>
>
> [stack@undercloud ~]$ ironic node-show a62116c4-1daf-45e9-aa2d-ef8a4effdc20
>
> +------------------------+--------------------------------------------------------------------------+
>
> | Property               | Value
>                             |
>
> +------------------------+--------------------------------------------------------------------------+
>
> | target_power_state     | None
>                             |
>
> | extra                  | {}
>                             |
>
> | last_error             | During sync_power_state, max retries
> exceeded for node a62116c4-1daf-    |
>
> |                        | 45e9-aa2d-ef8a4effdc20, node state None does
> not match expected state    |
>
> |                        | 'None'. Updating DB state to 'None'
> Switching node to maintenance mode.  |
>
>
> I also deleted the undercloud node and re-ran a fresh install of the
> undercloud and I'm going to do a fresh baremetal install of the
> virthost now and document all steps one by for the quickstart.
>
> One question: does the upstream documentation for TripleO work for
> anyone (without quickstart?). For the virt-install I got the instack
> running, but that was a nightmare :-)
>
> Thx,
> -Arash
>
>
>
> Mit freundlichen Grüßen,
> Arash Kaffamanesh
>

> Like <https://www.facebook.com/cloudssky> | Follow
> <https://twitter.com/CLOUDSSKYONE>
>
> *Arash Kaffamanesh (GF)**
>
> Clouds Sky GmbH
> **Im Mediapark 4C*
>
> *50670 Köln*
>
> Tel.: +49 221 204 726 76
> Mobile: +49 177 880 77 34
> www.cloudssky.com <http://www.cloudssky.com/>
>
> **
>
>
> On Fri, Mar 25, 2016 at 8:20 PM, Dan Sneddon <dsneddon@redhat.com

> <mailto:dsneddon@redhat.com>> wrote:
>
>     On 03/25/2016 11:52 AM, Arash Kaffamanesh wrote:
>     > Hi,
>     >
>     > I'm trying to deploy OpenStack via TripleO quickstart in AIO / virt
>     > mode and I'm getting by the last step deploying the overcloud the
>     > following "Heat Stack create failed" message (There are not enough
>     > hosts available, due to Configuration has 4 errors, fix them before
>     > proceeding ????).
>     > *
>     > *
>     >
>     > After running openstack overcloud deploy I'm getting
>     *Configuration has
>     > 4 errors, fix them before proceeding*: (and I guess the problem lies
>     > somehow here with the "incorrectly configured driver_info"):
>     >
>     > [stack@undercloud ~]$ openstack overcloud deploy --templates
>     >
>     > Node uuid=a62116c4-1daf-45e9-aa2d-ef8a4effdc20 has an incorrectly
>     > configured driver_info/deploy_ramdisk. Expected
>     > "482254d3-4b0c-4c3f-b2ba-bdf34badbbd3" but got "None".
>     >
>     > Node uuid=a62116c4-1daf-45e9-aa2d-ef8a4effdc20 has an incorrectly
>     > configured driver_info/deploy_kernel. Expected
>     > "482254d3-4b0c-4c3f-b2ba-bdf34badbbd3" but got "None".
>     >
>     > Node uuid=cfc60017-36e8-4808-842d-8c65ffb5e4b1 has an incorrectly
>     > configured driver_info/deploy_ramdisk. Expected
>     > "482254d3-4b0c-4c3f-b2ba-bdf34badbbd3" but got "None".
>     >
>     > Node uuid=cfc60017-36e8-4808-842d-8c65ffb5e4b1 has an incorrectly
>     > configured driver_info/deploy_kernel. Expected
>     > "482254d3-4b0c-4c3f-b2ba-bdf34badbbd3" but got "None".
>     >
>     > *Configuration has 4 errors, fix them before proceeding.* Ignoring
>     > these errors is likely to lead to a failed deploy.
>     >
>     > Deploying templates in the directory
>     > /usr/share/openstack-tripleo-heat-templates
>     >
>     > 2016-03-25 17:45:13 [overcloud]: CREATE_IN_PROGRESS  Stack CREATE started
>     >
>     > 2016-03-25 17:45:13 [MysqlRootPassword]: CREATE_IN_PROGRESS  state changed
>     >
>     > 2016-03-25 17:45:14 [Networks]: CREATE_IN_PROGRESS  state changed
>     >
>     > .......
>     >
>     > 2016-03-25 17:47:15 [overcloud]: CREATE_FAILED  Resource CREATE failed:
>     > resources.Compute: ResourceInError: resources[0].resources.NovaCompute:
>     > Went to status ERROR due to "Message: No valid host was found. *There
>     > are not enough hosts available*., Code: 500"
>     >
>     > *Stack overcloud CREATE_FAILED*
>     >
>     > *Heat Stack create failed.*
>     >
>     > [stack@undercloud ~]$ heat stack-list
>     >
>     > +--------------------------------------+------------+---------------+---------------------+--------------+
>     >
>     > | id                                   | stack_name | stack_status  |
>     > creation_time       | updated_time |
>     >
>     > +--------------------------------------+------------+---------------+---------------------+--------------+
>     >
>     > | 27fd6b76-7413-4e9b-9b5e-c7afb941ee0e | overcloud  |
>     *CREATE_FAILED* |
>     > 2016-03-25T17:45:12 | None         |
>     >
>     > +--------------------------------------+------------+---------------+---------------------+--------------+
>     >
>     >
>     > By the way I tried to get the stable liberty and the latest mitaka
>     > working with TripleO, no either worked.
>     > And tried also Lars's tutorial here:
>     >
>     > http://blog.oddbit.com/2016/02/19/deploy-an-ha-openstack-development-envir/
>     >
>     > had not so much luck, but could learn a lot and would prefer to learn
>     > more by running the ansible playbooks by hand as described by Lars.
>     >
>     > Any help / advice is much appreciated.
>     >
>     > Thx,
>     > -Arash
>     >
>     >
>     >
>     >
>     > _______________________________________________
>     > Rdo-list mailing list

>     > Rdo-list@redhat.com <mailto:Rdo-list@redhat.com>
>     > https://www.redhat.com/mailman/listinfo/rdo-list
>     >
>     > To unsubscribe: rdo-list-unsubscribe@redhat.com
>     <mailto:rdo-list-unsubscribe@redhat.com>
>     >
>
>     This sounds like the nodes either weren't introspected properly, have
>     incorrect boot settings, or do not meet the criteria for your flavors.
>
>     In particular, did you possibly forget to run "openstack baremetal
>     configure boot"? This has to be run after you import the nodes from
>     instack_env.json, and it will assign the kernel and ramdisk to the
>     nodes.
>
>     The instructions for this process begin here:
>     http://docs.openstack.org/developer/tripleo-docs/basic_deployment/basic_deployment_cli.html#introspect-nodes
>
>     You want to make sure that when you run "openstack baremetal
>     introspection bulk start" that the introspection completes
>     successfully. You can then use "ironic node-list" and "ironic node-show
>     <UUID>" to see the basic info about the host. The default baremetal
>     flavor requires 4G of RAM and 40G of hard drive space. Do your nodes
>     meet that minimum criteria? That's another cause of the "not enough
>     hosts available", although I think the configure boot setting is a more
>     likely culprit.
>
>     If you are trying to assign nodes to roles (Controller, Compute, etc.),
>     then you will want to review this section:
>
>     http://docs.openstack.org/developer/tripleo-docs/advanced_deployment/profile_matching.html
>
>     --
>     Dan Sneddon         |  Principal OpenStack Engineer
>     dsneddon@redhat.com <mailto:dsneddon@redhat.com> |
>     redhat.com/openstack <http://redhat.com/openstack>
>     650.254.4025        |  dsneddon:irc   @dxs:twitter
>
>     _______________________________________________
>     Rdo-list mailing list
>     Rdo-list@redhat.com <mailto:Rdo-list@redhat.com>
>     https://www.redhat.com/mailman/listinfo/rdo-list
>
>     To unsubscribe: rdo-list-unsubscribe@redhat.com
>     <mailto:rdo-list-unsubscribe@redhat.com>
>
>

That introspection doesn't look right. Are you sure that you imported
the nodes?

"openstack baremetal import --json instackenv.json"

You should then see the nodes actually being introspected. Does
anything show up now in an "ironic node-list"? Try deleting whatever
shows up in that list with "ironic node-delete <UUID>", then run the
import command above, followed by "openstack baremetal configure boot",
followed by "openstack baremetal introspection bulk start".

Start here, and make sure you follow all the steps:

http://docs.openstack.org/developer/tripleo-docs/basic_deployment/basic_deployment_cli.html#register-nodes

--
Dan Sneddon         |  Principal OpenStack Engineer
dsneddon@redhat.com |  redhat.com/openstack
650.254.4025        |  dsneddon:irc   @dxs:twitter